JPSC Forum

Moving house imminently so having a clear out. All parts are located in Macclesfield, but travel around UK a fair bit so delivery could be an option or can post at cost. Pics available for all items:

1) Alifab fuel tank. Bought to meet IVA regs, in car for <250 miles. 2" dia filler, vent inlet, return line inlet, single outlet from tank sump to avoid starvation from fuel surge. Location for level sender. Straight swap for fisher plastic tank, could fit many other kits / locosts. Drawing available, as are pics. £185 new, £100 ono? SOLD

2) Type 9 electronic speedo sensor + adaptor, brand new and sealed in packaging. Burton Power part numbers REVFSS and REVT9-A. RRP £50, £30? SOLD

3) 122.5mm Hella fog lamp, boxed. rrp £16 from SVC, £8?

4) Long wheel studs, 40 splines, 63mm overall length, 12mm x 1.5 so Ford or Vx. Qty 18. £10?

5) Decibel inserts to quieten exhausts down, 2.5" dia, part number JETU936330 from DT. 1 new, 2 used, £14 RRP each, £20 for all 3? ONE SOLD, TWO LEFT

6) Escort handbrake lever from Rally design, part number RD6901, RRP £16, £8?

7) Caterham race GRP seats, low backs with '7' embossed in place. Some scuffing, £20 for the pair? BOTH SOLD

8) Caterham pre S-type fabric seats, one modded so seat back is parallel to fury bulkhead, the other modded to take a crotch strap. £20 the pair? SOLD

Free to a good home:
90 deg mandrel bend 2.5" dia, slight surface rust, easy clean up.
9" Sierra rear drum brake shoes. and some 10" also. New.
MkII escort steering wheel. Round, large, energy absorbing boss, brown.

Cheerio,

Rob
(rob_j_hopkins@hotmail.com, 07812 157227)

Can you post up the dimentions/pictures of the tank? Is it a copy of the smaller (6.5 gallon) Fisher tank? If the filler is in the same place I'm interested.

I'm after a dB insert. Car is loud but only need 1

I have e-mailed.

Matt

I'd be interested in the speedo sensor and adapter PM sent too

Cheers Mark

Hi Adi,

The tank is a direct swap for my Fisher plastic tank, which I think is the smaller of the two. Filler neck is in the smae place, I think I made the ali tank slightly shallower to increase clearance from the lower edge of the tub.
Here's the drawing...

Fuel_tank_drg R2 by rob_j_hopkins, on Flickr

Here's the tank as delivered, you can see the extra vent adjacent to the filler...

IMG_2864 by rob_j_hopkins, on Flickr


IMG_2862 by rob_j_hopkins, on Flickr


IMG_2861 by rob_j_hopkins, on Flickr

The tank's out the car so quite happy to meet up should you want to measure / give it the once over?

Cheers,


Rob

PM sent re the tank.

adrian

Interested in the seats if they are what I am looking for!?!

Any pics please. Will they fit a Striker?
Cheers,

Biz

Hi Biz,

Seats are all ex-Caterham, two pre S-type fabrics, two low back fibreglass race seats.

Fabric seats:
Fixed back; one has been tweeked to a more upright position to give better legroom when fitted in the passenger side of a Fury. The other has a mod in the seat base to allow a fifth point for a harness (see above). I've got one set of runners, and one headrest which is now part of the requirement for IVA. Someone (hi Matt D!) currently has dibs on the seat with the harness mod.


The race seats are the pre-tillet caterham design with a low back; both have some scuffing, from memory one has a small crack in the RH edge, and the other is in Dorset in my folks attic so can either go straight from there or I can fetch it up to Macc.

Both types fit comfortably in a Fury, seat width is 410mm for the fabrics, 390 for the race seats. Think the striker is a broadly similar chassis so can't see these not fitting.

Cheerio,

Rob

A Striker has a significantly narrower cockpit than a Fury - check the cockpit width measurement.

Pete

Hi Rob

Thanks for the pics

Said yes to the fabric seats via email.
Should keep her indoors Rs intact.

Matt